[ad_1]
It has been a really lengthy and seemingly infinite course of, however yesterday I lastly put the ending touches on the IKEA cupboards that I used on the mural wall. They’re now utterly put in and completed, and as quickly as I get the outlet state of affairs completed up, I’ll be prepared to begin organizing issues in my cupboards and drawers. Because the posts about this mission have been unfold out over an extended time frame, and I didn’t really end the ultimate step (the filler strips) till yesterday, I needed to place the entire details about putting in IKEA cupboards in my studio in a single submit to point out all the course of from begin to end.
However first, right here’s a glimpse of the completed cupboards, full with the completed toekick and the filler strips between the cupboards and the facet partitions.
So let me begin from the very starting and provides a walkthrough of all the course of that I used, from begin to end, to put in these IKEA Sektion cupboards on the lengthy mural wall of my studio.
1. Connect the hanging rail to the wall.
I didn’t really use IKEA’s hanging rails as a result of I forgot to get them organized, and the transport prices on these alone would have been ridiculously costly. (I don’t dwell near an IKEA.) So as an alternative, I simply used 1″ x 4″ lumber throughout all the width of the wall screwed into studs.
I additionally put a narrower strip about 5 inches from the ground to behave as a spacer for the underside of the cupboards to carry them off of the wall on the identical distance.
2. Set up the toes on the cupboards (IKEA Sektion toes various)
I additionally didn’t buy IKEA’s toes for the Sektion cupboards as a result of they have been too tall for my functions. I wanted my cupboards to be not more than 33″ excessive, which signifies that my toes could possibly be not more than 3″ excessive. The minimal top for IKEA’s adjustable Sektion legs is 3.5″.
So I used some cheap lumber, ran it by way of my desk noticed to chop it down to three″ broad, after which reduce items that have been about 4″ lengthy. I glued and nailed 4 items collectively to make every foot, as proven beneath.
After which I connected them to the underside of the cupboards utilizing sizzling glue. I’ll repeat this once more. No woodworker must be utilizing a tiny craft retailer sizzling glue gun. Go to Residence Depot or one other huge dwelling enchancment retailer, go to the device part, and purchase your self a giant sizzling glue gun that may put out a complete lot of glue with every squeeze of the set off.
3. Connect the cupboards to the rails.
You’ll must be sure you rigorously learn the directions (correction: rigorously take a look at the drawings within the wordless instruction pamphlets) that include the IKEA Sektion cupboards as a result of the way in which during which you put in the mounting brackets onto your cupboards is set by whether or not or not you might be utilizing IKEA’s hanging rails. If you’re, the brackets are connected utilizing one set of holes. In the event you’re not (I didn’t), then the brackets are connected utilizing one other set of holes.
Since I wasn’t utilizing IKEA’s hanging rails, I connected my brackets appropriately in order that they might screw proper into the mounting board I had connected to the wall. I measured rigorously and positioned every cupboard the place I needed it, after which screwed a mounting screw by way of the massive gap within the bracket and into the board.
After which I hung this little bracket (these include the IKEA Sektion {hardware}) over every screw, however I didn’t tighten them utterly at this level. I needed the cupboards to nonetheless be capable of transfer just a little bit.
Right here’s what the cupboard appeared like from the facet view at this level…
4. Screw the cupboards to one another.
With the cupboards positioned within the appropriate order alongside the wall, and secured loosely to the board that was screwed into the studs, I used to be able to screw the cupboards to one another.
This took a while to get it excellent, and required a minimal of three clamps to carry the cupboards collectively as I used to be screwing them collectively. The cupboards don’t include these screw holes pre-drilled, and the directions don’t say to pre-drill the holes, however I did pre-drill as a result of it’s simpler and there’s much less of an opportunity that you simply’ll crack the melamine in case you pre-drill the holes. The screws which might be used to screw the cupboards collectively include the cupboards.
5. Tighten the cupboards to the mounting strip
As soon as the entire cupboards have been in place and screwed to one another, I went again and tightened these screws holding the cupboards to the mounting strip on the wall. I used my degree with each to verify I wasn’t getting the cupboards out of degree whereas tightening the screws.
Right here’s what it appeared like at this level with the entire cupboards screwed to one another and tightened to the wall.
6. Set up the toe kick
I had initially not deliberate to do a toe kick. I had deliberate to trim out the underside of the cupboards and not using a toe kick such as you would with a built-in bookcase. However later, I made a decision to do a toe kick as an alternative, which meant that I wanted to maneuver the toes again just a few inches.
I might have averted this trouble had I deliberate a toe kick from the start and positioned the toes the suitable distance from the entrance of the cupboard packing containers. But it surely wasn’t that huge of a deal, and it wasn’t something just a few whacks with a hammer couldn’t repair.
I used the hammer to loosen the new glue, then moved the toes again the place I needed them for a toe kick, and re-glued them.
After which the toe kick simply connected proper to the entrance of these block toes. IKEA sells toe kick strips to match all of their cupboards, however since I painted my cupboards a customized coloration, I simply used leftover lumber for my toe kicks. I needed to rip the boards on my desk noticed to get the precise 3-inch top, nevertheless it labored simply fantastic. I painted them to match the cupboards first, after which nailed them into place.
7. Add filler strips between cupboards and wall.
The final step was to fill within the areas between the cupboards and the facet partitions. I used 2″ x 2″ lumber (which is de facto 1.5″ x 1.5″) for this. The cupboard packing containers are 30″ excessive, so I reduce a 2″ x 2″ to about 28 inches in size, after which I used my sizzling glue gun to attach this to the facet of the cupboard with the entrance flush with the entrance fringe of the cupboard field. As soon as the glue dries, you may comply with up with screws in the identical method that the cupboards have been screwed collectively. I opted to simply use the glue, although.
As soon as the glue was utterly dry, I put the door on and measured the house between the sting of the door and the wall. I used my desk noticed to chop a bit of lumber to suit the width of that house (minus about 3/16″), after which used my miter noticed to chop the size to 30″ (the identical top because the door). I connected this to the wooden spacer piece behind it utilizing 16-gauge 1.5″ nails.
Once more, IKEA sells filler strips that match all of their cupboards, however since my cupboards are painted a customized coloration, I simply used scraps of lumber that I had readily available.
Word: I used IKEA’s Veddinge cupboard doorways and drawer fronts, that are 5/8″ thick. To ensure that my spacer strip to be the identical, I ran this board (commonplace 1″ lumber, which in fact, is barely 3/4″ thick in actuality) by way of my planer to shave off that further 1/8″ of thickness in order that it might match the thickness of the Veddinge doorways. In the event you don’t have entry to a planer, and your doorways are additionally 5/8″ thick (relying on the type you select), you may need to transfer the primary spacer strip again about 1/8″ in order that the entrance completed spacer board received’t look thicker than the doorways. Or you may keep away from that trouble by utilizing IKEA’s matching filler strips.
And eventually, I caulked the little house between that filler strip and the wall, wooden crammed and sanded the nail holes, after which primed, painted, and clear coated the spacer to match the cupboards.
After which I repeat that entire course of on the opposite finish of the cupboards. And with that, the cupboards have been utterly put in and completed.
This was a reasonably simple and easy course of since this was a financial institution of cupboards that stretched from one facet wall to a different.
It’s a way more difficult course of when you could have a whole facet of the cupboards utterly uncovered, and you need to end off all the facet to look completed. That’s the state of affairs I’ll be coping with on the opposite part of cupboards, so I’ll share that course of quickly.
Word: This submit was only a recap of the set up course of. However if you’d like extra details about how I trimmed, painted, and accented my IKEA Sektion cupboards with the Veddinge doorways and drawer fronts, or how I constructed my 20-foot-long countertop, you may examine these tasks by clicking the titles beneath:
Addicted 2 Adorning is the place I share my DIY and adorning journey as I transform and enhance the 1948 fixer higher that my husband, Matt, and I purchased in 2013. Matt has M.S. and is unable to do bodily work, so I do the vast majority of the work on the home on my own. You may be taught extra about me right here.
[ad_2]
Source link
