[ad_1]
Progress on the storage cupboard for our toilet is transferring alongside. I bought the entire thing trimmed out, and now it’s prepared for all the ending — wooden filling, sanding, caulking, priming and portray. That is Half 2 of this undertaking, so in the event you missed the primary publish about this DIY storage cupboard, yow will discover the DIY particulars concerning the fundamental construct right here. When you’re all caught up, let me present you the way I went from this very fundamental and plain cupboard…
…to this trimmed out cupboard that’s now prepared for ending and paint.
*This publish comprises affiliate hyperlinks.
1. Add the furnishings toes
I made a decision that I needed the cupboard to be off of the ground, so I bought 4 of those furnishings toes from Dwelling Depot. These toes include a threaded publish already inserted into the highest, and the best technique to connect them is by screwing these heavy obligation high plates to the underside of the furnishings, after which screwing the ornamental foot into that plate.
Nevertheless, I used to be working on my own in a really restricted work space, so there was no attainable method I might screw these high plates onto the underside of the cupboard. So as an alternative, I eliminated the threaded publish from the toes utilizing some pliers and simply unscrewing it from the foot, after which I lifted every finish of the cupboard up simply sufficient to get the toes beneath. I wasn’t too involved about excellent placement initially. I simply wanted to get all 4 toes underneath the cupboard in order that the cupboard was resting on the toes.
After I had all 4 toes underneath the cupboard, I might then transfer them into place. I gained’t lie. This wasn’t simple, and it took some persistence, however I lastly bought all 4 toes into place. Then I secured them into place by utilizing 2.5-inch screws, and screwing these by the within backside of the cupboard and into the toes. I ended up utilizing two screws per foot.
2. Trim out the underside of the cupboard
To trim out the underside of the cupboard, I began by slicing 1″ x 5″ pre-primed fingerjoint boards and attaching them alongside the underside fringe of the cupboard. I used my miter noticed to chop these items, and so they have straight cuts alongside the again edges of the cupboard, and mitered cuts alongside the entrance corners of the cupboard. I connected them with wooden glue and 1.5-inch 16-gauge nails in my nail gun.
Subsequent, I used cove molding (you possibly can see what that appears like right here) alongside the highest fringe of the 1″ x 5″ board. I reduce this with my miter noticed as nicely, making straight cuts alongside the again fringe of the cupboard, and mitered cuts on the entrance corners. I connected this with 5/8-inch 18-gauge nails in my nail gun.
To complete out the underside edge, I reduce and connected this 1 3/16-inch cupboard trim proper alongside the underside fringe of the 1″ x 5″ board. I connected this utilizing 5/8″ 18-gauge nails.
3. Connect the crown molding
To complete the highest of the cupboard, I put in this crown molding throughout the highest. When putting in crown molding, I all the time use my Kreg Crown Professional Crown Molding Software. I used to completely hate putting in crown molding, and I’d find yourself with an enormous pile of wasted crown as a result of I simply couldn’t determine the cuts. Ever since I bought the Kreg Crown Professional, I discover slicing crown molding to be fairly simple. I gained’t go into element on this publish about how one can use the Kreg Crown Professional to chop crown molding, however if you need extra particulars, you possibly can see this publish the place I defined the method.
4. Trim the ugly and uncooked edges
The ultimate step to trimming out the cupboard was so as to add this smaller cupboard trim to cowl over the uncooked and ugly edges. I connected these with 5/8″ 16-gauge nails.
On the entrance facet edge, that piece would have usually lined over all the joints. Nevertheless, if since I doubled up on the face boards for this cupboard (which I did as a result of I used precise 1/5-inch-thick inside doorways for this cupboard and I needed the face board to be the identical thickness), that implies that my facet trim alongside the entrance edge didn’t cowl all the joints. If I had used a traditional single thickness face body, this wouldn’t have been a problem. And if this cupboard have been going to be in a spot the place the edges could be plainly seen, I may need give you one other trim answer. However because the sides of my cupboards don’t actually present in any respect on this small room, I made a decision to not fear about it.
And eventually, I connected one other piece of that very same trim alongside the entrance facet edges. This can all mix in significantly better as soon as all the things is painted the identical colour.
And with that, all the trim was completed, and it’s now prepared for the ending course of, beginning with wooden filling and sanding all the nail holes.
I do nonetheless want to put in cabinets inside, however I need to prime and paint the inside first, after which paint the cabinets and add them afterwards.
Somebody requested me if the cupboard was masking the final column of butterflies. The cupboard does stick out sufficient to the place the entrance fringe of the cupboard is about even with the within fringe of the proper vertical body piece. Which may trouble some folks, but it surely doesn’t trouble me in any respect. There’s by no means a time when somebody could be to this point into the room, and to this point on the opposite facet of the cupboard, that that final column of butterflies could be lined up. Because the butterflies will all the time be seen from an angle, they’ll all the time be utterly seen even with the small overlap.
After which I had an individual specific concern that the door wouldn’t open all the way in which as soon as the bathroom is put in. There’s really loads of room. You’ll be able to see the place the bathroom will go (don’t fear…that’s a model new wax ring in an space the place a bathroom has by no means been used, so it’s actually not as gross because it appears 😀 ), and when the door is open, there’ll nonetheless be about 13 inches between the sting of the door and the bathroom. So there’s loads of room.
So right here’s what the cupboard appears like now that it’s all trimmed out.
My purpose is to get it completed this weekend in order that I can present you the ultimate cupboard on Monday, however I make no guarantees. 🙂 I’m going to do my greatest, although.
Addicted 2 Adorning is the place I share my DIY and adorning journey as I rework and embellish the 1948 fixer higher that my husband, Matt, and I purchased in 2013. Matt has M.S. and is unable to do bodily work, so I do the vast majority of the work on the home on my own. You’ll be able to be taught extra about me right here.
I hope you’ll be part of me on my DIY and adorning journey! If you wish to comply with my tasks and progress, you possibly can subscribe under and have every new publish delivered to your e-mail inbox. That method you’ll by no means miss a factor!
[ad_2]
Source link
